× Limited Time Offer ! FLAT 20-40% off - Grab Deal Before It’s Gone. Order Now
Connect With Us
Order Now

AURTTA017 Carryout Vehicle Safety Inspection Assignment Sample

1)List five (5) important items of personal protective equipment (PPE) you need when conducting safety inspections on vehicles.

Question 1

The five important items of personal protective equipment needed when conducting a safety inspection on the vehicle are;
? Hand gloves
? Safety helmet
? Safety shoes
? Gowns and aprons
? Safety mask

All this personal protective equipment is very important as the vehicle has several sharp points on which the vehicle inspector can get damage. Hand gloves will allow the vehicle inspector to get rid of any cuts from the edge corners of the vehicles. As opined by Alimohammadi et al. (2018), safety shoes will protect the feet of the inspector if the vehicle starts moving and hits the feet. After that safety helmet will give safety from the head bang in the vehicle's roof or bonnet. Finally, the safety mask will keep safe from the hazardous emission of the vehicles from the tailpipe.

2)List five (5) precautions when jacking and supporting vehicle using floor jackand stands.

Question 2

When jacking and supporting the vehicles by using a floor Jack and stand, some precaution needs to be taken, and among the five main precautions are as follows;
? It is very much important not to put the body part under the vehicle supported by the Jack as it can increase the chances of personal injury.

? Before putting the vehicle on the Jack, the vehicle must stop on level, firm ground, and must set the parking brake and put the transmission into 'P' mode in automatic vehicles and reverse mode in the manual vehicle (Emeka, 2019).

? Must need to set the Jack properly in the mentioned jacking point as improperly Jack position can damage the vehicle, or it can allow the vehicle to fall from the Jack, which cause personal and vehicle damage.

? Do not raise the vehicle in the vehicle lifter when someone is already inside the vehicle.

? It is important not to use the inferior Jack as it can damage the vehicles or can cause personal injury.

3)Why do we need to use stands and not jacks when working under vehicles?

Question 3

It has been identified that the vehicle support stands are very much important to provide stability to the vehicle after it is raised by using a hydraulic or manual Jack. Most of the time, Jacks do not provide adequate stability, and it is not a perfect situation for anyone to work under a lifted car (Productsafety, 2022). When more than one person is going to work under the vehicle, therefore, it will be very much important to use the safety stands as if any mechanical or hydraulic failure takes place, then the people will be in danger. Due to these conditions, it is very much important to use the stem when working under the vehicles.

4)List five (5) precautions that should be observed when a vehicle is to be raised on a hoist?

Question 4

Five precautions that must need to be observed when the vehicle is raised on a hoist;

? It is very much important to keep the lift area free from any kinds of abstractions and grease, oil, and other debris as it can increase the chances of personal risk or injuries.

? It is important to check the inside of the vehicle and just need to ensure that no one is inside the vehicle and all the people are standing at least 6 feet away before lifting the vehicle.

? It is very much important to ensure that all the hoisting cables are strong enough to support the full load of the vehicle (Workshopequipmentstore, 2022)

? It is important to lift the load very slowly and needs to ensure that the vehicle is not swinging.

? Before hoisting the vehicle, it is also important to properly check the over it clearance and must need to close all the doors and bonnet as well as the boot.

5)List five (5) major safety related items or systems that are checked on Am vehicle undergoing a safety inspection.

Question 5

There are several things present that must need to be checked when conducting a safety inspection inside the vehicle, and these things are as follows;

? It is very much important to test the brakes and must point out any types of brake oil leakages. It is also important to check the width of the brake pad through proper measurement tools.

? It is important to check whether the seat bills are in proper working condition as it is the primary safety device to keep the driver saved and allow them to survive a road accident. It is important to check whether the seat bills are adequately locked and have a proper grip.

? It is important to examine the defrosters and heating of the vehicles to remove the Frost or a layer of fog from the windshield during the wintertime.

? Must need to check all the vehicle lights, such as headlights and tail lights, to ensure that both high and low beams are working properly

? They just need to check the depth of the tires and the tire brake pressure. It is also important to identify any cuts or breaks in the wall of the tire.

6)Why is it important that the job card and vehicle safety inspection report are completed correctly?

Question 6

The vehicle job card provides an overview of the job that needs to be done on the vehicle when it is standing in the service bay. It is important to complete the job card properly as it indicates that all the jobs have been done properly, and it will also allow us to identify that no jobs are left, and the vehicle is now on release condition. On the other hand, a vehicle safety inspection report is also very important for identifying that there are no possible hazards that can damage the vehicle when it is moving on the road. It also brings satisfaction to the vehicle owners as they are safe to drive.

7)Which source will give you the most detailed information about how a safety inspection should be conducted on a vehicle? Select one answer only

A. Any vehicle’s workshop manual
B. Any vehicle’s owner’s manual
C. Actual vehicle’s owner’s manual
D. Actual vehicle’s workshop manual
E. Textbooks

Question 7

The best way to get all the most detailed information for assignment help about the safety of the vehicles is the any vehicle’s workshop manual. As mentioned by Wang et al. (2020), vehicle safety is the key to the longevity of the vehicles, and by putting the safety of the vehicle, the driver can also rely on the functionality of the automobile. That is the reason why for the safety of the vehicles, the first and foremost manual that is required is any vehicle's workshop manual. With the help of the manual, the driver can identify all the essential perks and potential threats to the safety of the vehicle, and by doing that, the driver can mitigate all the risks to the vehicle’s safety. With the identification of the potential threats, the driver can get all the safety precautions for the vehicles for the long term.

8)A safety check is not a complete assessment of a vehicle’s compliance with the Standards for Registration which, in most cases, are the Australian Design Rules (ADR’s). Is this statement true or false?

Question 8

Yes, the statement is true for two of the major reasons that are essential for the betterment of vehicle servicing, and that is the reason why the ADR or the Australian Design rules are essential for the vehicle's safety. As per the views of Wiseman, Kariyawasam & Davey (2020), the ADR or the Australian Design Rule is the guideline for the discharge process of any kind of vehicle, and thus, getting along with the process is the most crucial part of the rules. For the safety of the vehicle, there are some steps that are needed to be taken, and that is the reason why to take all the necessary steps for the discharge of the vehicles after the initial safety check, the vehicles need to be checked for the technical requirements so that if the vehicle carries forward any of the heavier staffs that are essential for the driver.

9)What is the technician doing in the picture below? Answer in one sentence.

Question 9

In the given picture, the person is checking the health of the engine and checking all the essential parameters that are there for taking the vehicles to the assembly.
10)List three (3) methods for sourcing the specifications for the servicing of a vehicle.

Question 10

Servicing any of the vehicles is essential, and by doing that, the vehicles can be fully functional. Vehicle safety is the key to the longevity of the vehicles, and by putting the safety of the vehicle, the driver can also rely on the functionality of the automobile. That is the reason why for the safety of the vehicles, the first and foremost manual that is required is any vehicle's workshop manual. As mentioned by Kazi et al. (2018), the essentiality of the vehicle's safety and the maintenance of the vehicle is essential for the betterment of the vehicles. For the safety of the vehicle, there are some steps that are needed to be taken, and that is the reason why to take all the necessary steps for the discharge of the vehicles. The three methods of the vehicle's maintenance are- checking all the fluids, checking all the batteries, and inspecting the exhaust system. All these steps are essential for the overall safety of the vehicles, and that is the reason why these steps need to be inspected and monitored thoroughly.

References

Fill the form to continue reading

Download Samples PDF

Assignment Services